Pi & Accs
Orange Pi SBC and accessories for Pi and Arduino
Orange Pi Zero plus2 H3 (OPi0ZeroPlus2H3)
Supported OS - Debian, Ubuntu, Android
on-Board 8G emmc storage
- CPU - H3 Quad-core Cortex-A7 32bit 1.2 GHz
- GPU - Mali 400MP2 - HDMI HDCP, CEC, HDMI 30
- Memory - 512MMB DDR3 RAM (Shared with GPU)
- Storage on-board 8G emmc + µSDRAM-TF card slot up to 32GB
- Spi Flash for boot control
- Onboard WiFi - AP6212, IEEE 802.11 b/g/n, BT4.2
- USB OTG can be used for input power.
- 26 Pin GPIO, compatible with Raspberry Pi B+
- 13 Pin Header, with 2x USB, IR pin, Audio, Mic, AV used by expansion board
- Power & Status LEDs
Supported OS - Debian, Ubuntu, Android
Pre-Loaded Android OS is Free.
Orange Pi Zero plus2 H3
Out of Stock
CAD$79.99
Orange Pi Zero 512M - LTS (Opi0512)
Just like R Pi Zero - but faster
Supported OS - Android, Lubuntu, Debian, Raspbian
- CPU - H3 Quad-core Cortex-A7 1.2 GHz
- Memory - 512MB DDR3 SDRAM (Shared with GPU)
- Storage µSDRAM-TF card up to 32GB
- Spi Flash for boot control
- Onboard Network - 10/100M Ethernet RJ45 (POE)
- Onboard WiFi - XR819, IEEE 802.11 b/g/n
- USB 2.0 + OTG used for input power.
- 26 Pin GPIO, compatible with Raspberry Pi B+
- 13 Pin Header, with 2x USB, IR pin, Audio, Mic, AV
- Power & Status LEDs
Supported OS - Android, Lubuntu, Debian, Raspbian
Pre-Loaded OS is Free with microSD card.
Orange Pi Zero 512M - H3
Orange Pi Zero Expansion (pi0exp)
Orange Pi Zero Expansion Board
provides:- Two USB 2.0 type-A ports
- Composite Audio/Video output (1/8" jack)
- Microphone
- IR Receiver
- connects via 13pin header
2xUSB, composite A/V, mic and IR
FTDI Break Out USB to UART (FTDI-BO)
- Connect to your Pi or Arduino Serial Port via USB
FTDI USB to UART Converter with Break Out
Orange Pi Zero Case (Opi0case)
3D printed to hold Orange Pi Zero and expansion board.
Orange Pi Zero Enclosure
FTDI USB to UART (FTDI)
- Connect to your Pi or Arduino Serial Port via USB
- Connect the 3 female jumper connectors to your development board's RX, TX and GND pins
- Then use Putty to communicate with the corresponding COM port such as /dev/ttyUSB0
FTDI USB to UART Converter
RaspBerry Pi3 B+ Acrylic Case (Pi3Acrylic)
RaspBerry Pi3 B+ Acrylic Case
Optional Fan and/or HeatSink
Optional Fan and/or HeatSink
RaspBerry Pi3 B+ Acrylic Case - Fan / HeatSink
USB WiFi (WiFi)
USB to WiFi Adapter
JDY-31 BlueTooth module (JDY-31)
JDY-30 BlueTooth Classic Rs-232 module for Arduino or Pi
Android compatible - "AT" commands can select
Baud Rate, Name, etc.
Android compatible - "AT" commands can select
Baud Rate, Name, etc.
JDY-30/31 Slave Serial Xcvr - Android
Out of Stock
CAD$4.99
AT-09 BlueTooth BLE module (AT-09)
AT-09 BlueTooth Rs-232 module for Arduino or Pi
BLE - AT-09 IOS/Android compatible - "AT" commands
BLE - AT-09 IOS/Android compatible - "AT" commands
AT-09 BlueTooth BLE Serial module - IOS
Heat Sink Kit (HSink2)
2 pc Heat Sink Kit for RaspBerry Pi
or Orange Pi
or ESP8266/ ESP32 / Motor Controller
Aluminium with peel off mounting tape.
2 pc Heat Sink Kit - RaspBerry
USB to UART (USBUART)
- Connect to your Pi or Arduino Serial Port via USB
- Connect the 3 female jumper connectors to your development board's RX, TX and GND pins
- Then use Putty to communicate with the corresponding COM port such as /dev/ttyUSB0
- The Prolific is NOT Recommended for Windows 8 or 10
USB to UART Converter 3.3V
- 1