Search
Search Criteria
Products meeting the search criteria
USB Cables (USBcable)
various cables...
"micro" is typically used for the Nano32 - 1m long
"mini" is typical for the "normal" Nano - 1m long
the "A" extension is good for the USBasp - 1m long
NOTE - the micro with switch is POWER-ONLY - no data - NOT for Uploading.. 2m long
- Colours may vary from photo.
"micro" is typically used for the Nano32 - 1m long
"mini" is typical for the "normal" Nano - 1m long
the "A" extension is good for the USBasp - 1m long
NOTE - the micro with switch is POWER-ONLY - no data - NOT for Uploading.. 2m long
- Colours may vary from photo.
Various USB Cables
FTDI Break Out USB to UART (FTDI-BO)
- Connect to your Pi or Arduino Serial Port via USB
FTDI USB to UART Converter with Break Out
USBASP (USBasp)
The ISP gives you the freedom to program all of the flash memory including the bootloader, you might want to use caution!!
Firmware upgrade eliminate the "unable to set sclk" error/warning
includes TPi protocol for programming ATtiny10 family of MCUs
- ATmega8 Chip - Tested on Win10 and Ubuntu
- 3.3V and 5V switch selectable.
- USB- connector
- 50cm 10 pin Ribbon cable
Firmware upgrade eliminate the "unable to set sclk" error/warning
includes TPi protocol for programming ATtiny10 family of MCUs
STK500 USBASP
FTDI USB to UART (FTDI)
- Connect to your Pi or Arduino Serial Port via USB
- Connect the 3 female jumper connectors to your development board's RX, TX and GND pins
- Then use Putty to communicate with the corresponding COM port such as /dev/ttyUSB0
FTDI USB to UART Converter
DC - DC Boost Wired or USB (Boost2A)
Input: 2 - 24 VDC
Output: 3 - 28 VDC - continuously variable
Current Output: max. 2A XL6009 Input: 3.8 - 32 VDC
Output: 4 - 38 VDC - continuously variable
Current Output: max. 4A - Typ. 2.8A
Output: 3 - 28 VDC - continuously variable
Current Output: max. 2A XL6009 Input: 3.8 - 32 VDC
Output: 4 - 38 VDC - continuously variable
Current Output: max. 4A - Typ. 2.8A
2A DC to DC Sterp-Up
USBASP w/Shell (USBaspSH)
The USBASP gives you the freedom to program all of the flash memory including the bootloader, you might want to use caution!!
NOTE: Shell Colours may vary...
Firmware upgrade eliminate the "unable to set sclk" error/warning
includes TPi protocol for programming ATtiny10 family of MCUs
- ATmega8 Chip - Tested on Win10 and Ubuntu
- 3.3V and 5V switch selectable.
- USB- connector
- 50cm 10 pin Ribbon cable
NOTE: Shell Colours may vary...
Firmware upgrade eliminate the "unable to set sclk" error/warning
includes TPi protocol for programming ATtiny10 family of MCUs
USBASP with Aluminum Shell
USB WiFi (WiFi)
USB to WiFi Adapter
USB BreakOut (USB_BO)
pins included for breadboard use...
ideal for adding OTG USB to the Saola
Nano uses miniUSB
Nano32 and ESP-XX use microUSB
BreakOut board for USB / OTG
USB Meter (USBmeter)
USB in-line Voltmeter, Ammeter, Power Meter
USB in-line Voltmeter, Ammeter, Power Meter
USB to UART (USBUART)
- Connect to your Pi or Arduino Serial Port via USB
- Connect the 3 female jumper connectors to your development board's RX, TX and GND pins
- Then use Putty to communicate with the corresponding COM port such as /dev/ttyUSB0
- The Prolific is NOT Recommended for Windows 8 or 10
USB to UART Converter 3.3V
BBoard PS - miniUSB (BBPSmini)
Power Adapter for Dual Power Rail BreadBoards - 830 and 400
miniUSB power input ( NANO cable )
Barrel Jack for other Wall Warts..
Power Adapter for Dual Power Rail BBoards
TP4056 Lithium Charger (TP4056)
1A TP4056 mini-USB Li-Ion Battery Charger/Protector Module
Note that this is a Mini-USB Module
1A TP4056 mini-USB Battery Charger
Out of Stock
US$2.19
USBasp adapter for ATtiny85/13A (TinyUSBasp)
USBasp Adapter for BreadBoarding ATtiny85/13A
Just place over the ATtiny chip and connect the USBasp cable to this adapter.
Ships with long pins to provide clearance.
my own design.
Just place over the ATtiny chip and connect the USBasp cable to this adapter.
Ships with long pins to provide clearance.
my own design.
USBasp Adapter for BreadBoarding ATtiny
- 1